Docs / Domain mappings / eurosynth
EuroSynth
Rig names a modular faceplate, its jacks, and its supply as rig.modular.*. EuroSynth and Eurorack are published numbers written into those fields. The names are not schema ids.
A jack publishes the window it accepts or produces. A panel publishes its fit. Two builders compare those numbers before a cable joins the modules.
The numbers below are the EuroSynth figures this document uses. New figures take a new spec id.
Thin layer
Do not invent rig.eurosynth.* or rig.eurorack.*. A jack's live voltage is host cache. Nominal width (hp * pitchMm) is host arithmetic. Finished width is widthMm when the spec or the calipers give it.
| Idea | Rig |
|---|---|
| Case, skiff, rack row | rig.modular.case |
| Module faceplate | rig.modular.module + rig.meta.named |
| Which published spec | A named entity (stableId eurosynth). Case and module spec point at it |
| Patch jack | Child rig.modular.port. Bushing colour is rig.paint.fill_stroke |
| Drawn panel, labels | Geometry and rig.media.text. Faceplate height is only in the mechanical drawing; set heightMm from a measurement |
| Module current and header | rig.modular.power on the module |
| Header contacts | rig.circuit.part + child rig.circuit.pin, each net pointing at a rig.circuit.net |
| Supply limits | Child rig.modular.rail |
| Chassis metal | Its own rig.circuit.net. Not the 0 V rail |
| MIDI DIN | rig.music.midi_input / midi_output. The CV and gate that MIDI becomes are ports |
Mechanical
Eurocard horizontal pitch. pitchMm is 5.08. hp is a whole number.
EuroSynth publishes a finished width per HP, shorter than hp * 5.08, so panels can sit side by side. That figure is widthMm. The example uses an 8 HP faceplate at 40.30 mm and an 84 HP opening at 426.40 mm. A host computes the nominal width as hp * pitchMm.
Panels state a general thickness of 2.5 mm (thicknessMm). The proposed module depth, from the inside face to the furthest rear point, is 60 mm (depthMm). A 19 inch sub-rack still allows 160 mm. A host compares module depthMm with case depthMm.
The thread is M3 (fastener m3). Eurocard's M2.5 is m2-5. EuroSynth uses M3, and prefers a slotted hole with a captive thumbscrew.
Every panel has two fixings on the left. A panel wider than 10 HP adds two on the right. In the published table those right-hand fixings sit 7.74 mm in from the nominal right edge (hp * 5.08 - 7.74, measured from the left). Vertical positions are in the mechanical drawing; place rig.spatial.vertex children when that drawing has been measured.
A PCB parallel to the panel is limited to (hp * 5.08) - 2 mm wide and 110 mm tall. Those are checks against a rig.pcb.board, not extra fields.
Power
EuroSynth uses a 10-pin boxed IDC header (header idc-10). Pin 1 of the cable is pin 1 of the header, and pin 1 is -12 V. Eurorack's 16-pin header (idc-16) uses the same first ten pins, then +5 V, CV, and gate. EuroSynth leaves those off. A module that still needs +5 V sets positive5MilliAmps. The adaptor is not in the document.
| Pins | function |
EuroSynth |
|---|---|---|
| 1, 2 | -12V |
kept, blue pair |
| 3, 4, 5, 6, 7, 8 | 0V |
kept, black |
| 9, 10 | +12V |
kept, red pair |
| 11, 12 | +5V |
16-pin only |
| 13, 14 | CV |
16-pin only |
| 15, 16 | GATE |
16-pin only |
electricalType on a module header is power-in.
Both 12 V rails are specified to hold:
| Limit | Field | Value |
|---|---|---|
| Tolerance | toleranceMillivolts |
10 |
| Load regulation | loadRegulationMillivolts |
10 (RMS) |
| Noise | noiseMillivolts |
10, from noiseMinHertz 10 to noiseMaxHertz 10000 |
| Path impedance | maxImpedanceMilliohm |
10, from any module terminal to the supply, cables included |
Omitted module current is not 0 mA. A stated 0 means that rail is unused.
Chassis is its own net, separate from 0 V. A panel part on the chassis is not also tied to the module 0 V net. Mains earth is not in this document.
Signals
connector banana-4mm is the EuroSynth jack. ts-3-5mm is the 3.5 mm Eurorack jack a mixed case still has to name. Input impedance in the spec is typically 100000 ohm and not below 47000. A 1 V/octave output is about 50 ohm. Other outputs are about 330 ohm. The schema accepts whatever was measured; a EuroSynth host can warn outside those bands.
tolerance is a fraction of highVolts: 0.10 is +/- 10%, 0.01 is +/- 1%.
| Jack | direction |
signal |
Window | Other |
|---|---|---|---|---|
| Control CV in | in |
cv |
0 V to +5 V, tolerance 0.10 | 1 V/octave. Middle C (MIDI 60) at 2.5 V, so 0 V to 5 V is about 35 Hz to 1 kHz. From 0 Hz |
| Modulation CV in | in |
cv |
-2.5 V to +2.5 V | From 0 Hz |
| Control CV out | out |
cv |
0 V to +5 V, tolerance 0.01 | Sensitive pitch output at about 50 ohm. Same 2.5 V Middle C |
| Audio in | in |
audio |
typical +/- 2.5 V (5 V peak-to-peak); specified out to +/- 5 V (10 V peak-to-peak) | From 16 Hz. Store the window the jack actually accepts |
| Audio out | out |
audio |
+/- 2.5 V | About 330 ohm. From 16 Hz |
| Gate in | in |
gate |
nominal 0 V and +5 V, tolerance 0.10 | Off at or below 1 V, on at or above 2 V, trip thresholdVolts 1.5. The spec also states +/- 0.1% on that trip |
| Gate out | out |
gate |
0 V and +5 V, tolerance 0.01 | Resting level, not the edge |
| Trigger in | in |
trigger |
Slew at least 0.3 V/us, transition at most 10 us | |
| Trigger out | out |
trigger |
0 V and +5 V, tolerance 0.01 | The edge must pass below 1 V and above 2.5 V. A 0 V to 5 V window does |
| VCA law | in |
cv |
decibelsPerVolt 12 when the jack is scaled at 12 dB/V. 5 V of that law is 60 dB, and 0 V is shut |
An open top ("greater than 15 kHz", "greater than 16 kHz") stays omitted. minHertz records the bottom that was stated.
Bushing paint, from the colour names the spec prints: CV in blue, CV out green, gate in red, gate out yellow, trigger in red, trigger out yellow. The spec names no audio colours in the text, so leave those bushings unpainted.
Eurorack, for a host comparing mixed rows: audio is often +/- 5 V (10 V peak-to-peak), control CV often 0 V to 8 V, modulation the same +/- 2.5 V, gate and trigger 0 V to 5 V, jacks ts-3-5mm, outputs often 1000 ohm. Compare lowVolts / highVolts and impedanceOhm. A brand match is not the check. A EuroSynth audio input specified to +/- 5 V accepts a Eurorack +/- 5 V output. A EuroSynth audio output at +/- 2.5 V sits inside a Eurorack input. An 8 V Eurorack CV does not sit inside a EuroSynth control input specified to 5 V +/- 10%.
Example: examples/eurosynth.json.